Parts Manual Intermediate Walk-Behind Snowthrowers 5HP Product Mfg. No. 1694587 1694595 Description 555M, 5HP 555M, 5HP 8HP Product Mfg. No. 1694588 1694596 Description 860E, 8HP 860M, 8HP Part No.: 1731153 Rev. 02/2008 TP 400-4148-01-IW-S Table Of Contents PRODUCT COMPONENTS PAGES 4 8 12 16 18 20 24 26 28 Handles & Controls Group . Engine, Pulleys, & Frame Group – 5HP Tecumseh . Engine, Pulleys, & Frame Group – 8HP Briggs & Stratton Auger & Impeller Group . Auger Housing Group Traction Drive Group Wheels & Tires Group Decals Group .
Snow Blower and Snow Thrower User Manual Free Download. Snow Removal Operator’s Manual. Free Service Manual Download PDF.
Download (Simplicity-5-8-HP-1694587-1694595-1694588-1694596-Intermediate-Snow-Blower-Thrower-Parts-Manual.pdf)
Chute Crank Control Group . Torque Specification Chart . Inside Back Cover Handles & Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070uhdc The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 4 TP 400-4148-01-IW-S Handles & Controls Group REF NO PART NO. 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 5025057SM 1726727ASM 1921332SM 7027426SM 1726574SM 1722638SM 1726317SM 1722460SM 1666255SM 1916622SM 1916964SM 1931317SM 1720238SM 1668524SM 1720240SM 1715123SM 1918452SM 1668185SM 1924361SM 1668523SM 1960705SM 1921319SM 1726734SM 1726983ASM 1726572SM 1716632SM 7090391SM 1960686SM 1919326SM 1722633SM 1722690SM 1960519SM 1722630SM 1960662SM 1722667SM 1923358SM 1715655SM 1726573SM 1922837SM 1715654SM 1960671SM 1921221SM 1722631ASM 1920397SM QTY. DESCRIPTION 2 1 4 1 1 1 2 3 1 2 3 2 1 2 1 1 1 2 1 1 1 2 1 1 1 2 2 4 2 1 1 1 1 1 1 2 2 1 2 2 2 5 1 2 NUT, 5/16-18 Hex Nyloc BRACKET, Snow Stick- Lower SCREW, 5/16-18 x 3/4 ” Hex Head Cap CLUTCH CABLE, Auger Drive- RH HANDLE, Upper, Right Hand GRIP, Clutch, RH GRIP, Foam, Black HAIR PIN ROD, Shift, Lower NUT, 1/4-20 2B Hex LOCKWASHER, 1/4 ” Spring BOLT, 1/4-20 x 2 ” Short Square Neck Carriage, GR 5 ROD, Upper, Shift BLOCK, Pivot SHIFT ROD PIVOT ASSEMBLY SPRING, Compression COTTER PIN, .125 x 1.00 BUSHING, .500 ID x .750 OD x .25 WASHER, 1/2 ” Flat (.531 ID x 1.250 OD x .08 Thick) SHIFT ROD ASSEMBLY SCREW, 1/4-20 x 2-1/4 ” Hex Flange Lock WASHER, .250 (.27 ID x .62 OD) KNOB, Tapered – 3/8-16 Internal Thread- Red DASH ASSEMBLY HANDLE, Lower WING KNOB, 5/16-18 WASHER, 5/16 ” Internal Tooth Lock NUT, 5/16-18 Hex Flange Nyloc WASHER, .312 (.34 ID x .75 OD) ASSEMBLY, Rod w/Pin (Includes Ref. Nos. 31. 47, 54, 55 & 56) SPRING, Compression PUSH NUT ROD, Hold Down SCREW, 1/4-20 x 2 ” Hex Head Cap, GR 5 GRIP, Clutch, LH NUT, 1/4-20 Hex Centerlock SPACER, Handle HANDLE, Upper, Left Hand SCREW, 1/4-20 x 1-1/2 ” Hex Head Cap SPACER, .268 ID x .394 x .165 SCREW, 1/4-20 x 3/4 ” Pan Head Torx Self-Tap SCREW, 5/16-18 x 1-1/2 ” Hex Head Cap, GR 5 LEVER, Pivot NUT, 1/4-20 Hex Nyloc Footnotes The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 5 TP 400-4148-01-IW-S Handles & Controls Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070uhdc The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 6 TP 400-4148-01-IW-S Handles & Controls Group REF NO PART NO. 45 46 47 48 49 50 51 52 53 54 55 56 7075909SM 7091267SM 1722632 1726728SM 7027425SM 7091740SM 7090011SM 7091266SM 1917356SM 1722635 1722634 1722613 QTY. DESCRIPTION 1 1 1 1 1 4 1 1 4 1 1 1 TOOL, Clean-Out NUT, #10-24 Hex Center Lock ROD, Hand Control, not shown; part of item 30 HOLDER, Clean-Out Tool, Upper CLUTCH CABLE, Ground Drive- LH BOLT, 5/16-18 x 2 ” Curved Head Square Neck GR 2 WASHER, #10 Internal Tooth Lock SCREW, #10-24 x 2 ” Hex Washer Head Machine, GR5 LOCKWASHER, Spring 5/16, not shown; part of item 30 BUSHING, .250 ID x .375 OD x .750, not shown; part of item 30 PIN, Clevis, not shown; part of item 30 SPRING, Compression, not shown, part of item 30 Footnotes The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 7 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 5HP Tecumseh NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070epi5t The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694595 – 555M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 8 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 5HP Tecumseh REF NO PART NO. 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 1921515SM 1924874SM 1725424SM 1920427SM * 1726942SM 1931277SM 1931277SM 1715092SM 2816169SM 7072566SM 1926018SM 1666001SM 1715559A 1929477SM 1960251SM 1924940SM 1674315SM 1922694SM 1715756A 1924856SM 1715111SM 1919381SM 1922127SM 1922127SM 7072555SM 7091819SM 1925125SM 1918451SM 1715112SM 1960268SM 2174870SM 2118414SM 1717393SM 1715127SM 1715118SM 1669313SM 2825160SM 1717320SM 7091810SM 1922755SM 1668477SM 1725379SM 1720237SM QTY. DESCRIPTION 4 1 1 3 1 1 3 1 1 2 1 6 2 1 2 4 3 2 4 1 4 1 2 3 1 1 9 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 SCREW, 5/16-24 x 3/4 ” Hex Head Cap, GR 5 WASHER, 5/16 ” Flat WIRE, Belt Stop LOCKWASHER, 5/16 ” Exterior Tooth ENGINE, 5HP Tecumseh, Model LH195SA-67427V HOSE, Oil Drain NUT, 5/16-18 Hex Flange Lock- small NUT, 5/16-18 Hex Flange Lock ROD, Idler ROLL PIN, 3/16 x 3/4 ” FRAME ASSEMBLY, Intermediate (Orange) SPEED NUT, 1/4-20 U-Type BUSHING, 1.00 long SUPPORT, Tie Bar SCREW, #10-24 x 1/2 ” Hex Washer Self-Tap JAM NUT, 3/8-16 Hex Center Lock WASHER, 3/8 ” Flat ROD, Belt Guide NUT, 3/8-16 Hex Nyloc Heavy Thin SUPPORT, Frame SCREW, 5/16-18 x 1/2 ” Hex Washer Self-Tap SUPPORT, Pivot WASHER, 5/16 ” Flat SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 COVER, Bottom, Orange SCREW, 1/4-20 x 5/8 ” Hex Washer Self-Tap WASHER, 7/16 ” Flat COTTER PIN, 1/8 x 3/4 ” IDLER ARM ASSEMBLY BOLT, 3/8-16 x 1-1/4 ” Short Square Neck Carriage SPACER, .377 ID x .75 OD x .312 Long PULLEY, Idler BELT, Auger Drive, V Groove BELT, Traction Drive, V Groove SPRING, Extension PAD, Brake RIVET, Blind ASSEMBLY, Idler Arm w/Brake Pad BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5 WASHER, 3/8 ” Flat (.41 ID x 1.00 OD x .13 Thick) PULLEY, Idler COVER, Belt SPRING, Idler- Extension Footnotes Note*See your local Tecumseh distributor for engine service parts. The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694595 – 555M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 9 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 5HP Tecumseh NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070epi5t The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694595 – 555M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 10 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 5HP Tecumseh REF NO PART NO. 45 46 47 48 49 50 51 52 53 54 55 56 57 58 7092031SM 2824819SM 1674325SM 7090201SM 1720313SM 7010061SM 7015861SM 1930645SM 7028090SM 7091075SM 7034169SM 7034254SM 7034251SM 7034239SM QTY. DESCRIPTION 1 1 1 2 1 1 1 1 1 1 1 2 2 2 JAM NUT, 5/16-24 Hex KEY – Hi Pro .125 x .625 HP 504 SAE1035 PULLEY, V Groove SET SCREW, 5/16-18 x 5/16 ” Hex Recess, Cup Point PULLEY, 2.75 OD KEY, 3/16 Square x 1 ” HARNESS CLIP NUT, 3/8-16 Hex Flange Lock Two Way MUFFLER GUARD, Domestic (Tecumseh) SCREW, #10-24 x 5/8 ” Hex Washer Self-Tap MUFFLER GUARD, Tecumseh Engine (CE/Export), not shown; Tecumseh p/n 127-18 SCREW. Tecumseh Muffler, not shown; Tecumseh p/n 42-671 LOCK WASHER, Tecumseh Muffler, not shown; Tecumseh p/n 36-351 WASHER, Tecumseh Muffler, not shown; Tecumseh p/n 36-195-1 Footnotes Note*See your local Tecumseh distributor for engine service parts. The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694595 – 555M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 11 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 8HP Briggs & Stratton NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070epi8b The above parts group applies to the following Mfg. Nos.: 1694588 – 860E 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 12 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 8HP Briggs & Stratton REF NO PART NO. 1 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 1921982SM 1924874SM 1725424SM 1920427SM * * 1726942SM 1931277SM 1931277SM 1715092SM 2816169SM 7072566SM 1926018SM 1666001SM 1715559A 1929477SM 1960251SM 1924940SM 1674315SM 1922694SM 1715756A 1924856SM 1715111SM 1919381SM 1922127SM 1922127SM 7072555SM 7091819SM 1925125SM 1918451SM 1725369SM 1960268SM 2174870SM 2118414SM 1717393SM 1725371SM 1715118SM 1669313SM 2825160SM 1717320SM 7091810SM 1922755SM 1668477SM 1725379SM QTY. DESCRIPTION 4 1 1 3 1 1 1 3 1 1 2 1 6 2 1 2 4 4 2 4 1 4 1 2 3 1 1 9 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 SCREW, 5/16-24 x 1-1/4 ” Hex Head Cap, GR 5 WASHER, 5/16 ” Flat BELT STOP, Wire LOCKWASHER, 5/16 ” Exterior Tooth ENGINE, 8 HP Briggs, Model 12E394, Type 0110, Trim E1 ENGINE, 8HP Intek (Metric) Briggs & Stratton Model 12E396, Type 0111, Trim E1 (CE/Export) HOSE, Oil Drain NUT, 5/16-18 Hex Flange Lock- small NUT, 5/16-18 Hex Flange Lock ROD, Idler ROLL PIN, 3/16 x 3/4 ” FRAME ASSEMBLY, Intermediate (Orange) SPEED NUT, 1/4-20 U-Type BUSHING, 1.00 long SUPPORT, Tie Bar SCREW, #10-24 x 1/2 ” Hex Washer Self-Tap JAM NUT, 3/8-16 Hex Center Lock WASHER, 3/8 ” SAE Flat ROD, Belt Guide NUT, 3/8-16 Hex Nyloc Heavy Thin SUPPORT, Frame SCREW, 5/16-18 x 1/2 ” Hex Washer Self-Tap SUPPORT, Pivot WASHER, 5/16 ” Flat SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 SCREW, 5/16-18 x 1-3/4 Hex Head Cap, GR 5 COVER, Bottom, Orange SCREW, 1/4-20 x 5/8 ” Hex Washer Self-Tap WASHER, 7/16 ” Flat COTTER PIN, 1/8 x 3/4 ” IDLER ARM ASSEMBLY BOLT, 3/8-16 x 1-1/4 ” Short Square Neck Carriage SPACER, .377 ID x .75 OD x .312 Long PULLEY, Idler BELT, Auger Drive V-BELT, Traction Drive SPRING, Extension PAD, Brake RIVET, Blind ASSEMBLY, Idler Arm w/Brake Pad BOLT, 3/8-16 x 1-3/4 Short Square Neck Carriage, GR 5 WASHER, 3/8 ” Flat (.41 ID x 1.00 OD x .13 Thick) PULLEY, Idler COVER, Belt Footnotes Note*See your local Briggs distributor for engine service parts. The above parts group applies to the following Mfg. Nos.: 1694588 – 860E 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 13 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 8HP Briggs & Stratton NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070epi8b The above parts group applies to the following Mfg. Nos.: 1694588 – 860E 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 14 TP 400-4148-01-IW-S Engine, Pulleys, & Frame Group – 8HP Briggs & Stratton REF NO PART NO. 44 45 46 47 48 49 50 51 52 53 54 55 56 2159106SM 2820438SM 2824819SM 1674325SM 1960619SM 1720313SM 2805850SM 7015861SM 1724064SM 1725665A 1727032SM 1727033SM 1930645SM QTY. DESCRIPTION 1 1 1 1 2 1 1 1 1 1 1 1 1 SPRING, Extension, .562 O.D. x 4.250 Long JAM NUT, 5/16-24 Hex KEY – Hi Pro .125 x .625 HP 504 SAE1035 PULLEY, V Groove SET SCREW, 5/16-18 x 5/16 ” Hex Recess, Cup Point PULLEY, 2.75 OD KEY, 3/16 Square x 1 ” HARNESS CLIP CORD, Electric Start GUARD, Muffler MUFFLER, Deflector- B&S CAPSCREW, Thread Rolling M4 x 0.7, Briggs p/n 226462 NUT, 3/8-16 Hex Flange Lock Two Way, Briggs p/n 810140 Footnotes Note*See your local Briggs distributor for engine service parts. The above parts group applies to the following Mfg. Nos.: 1694588 – 860E 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 15 TP 400-4148-01-IW-S Auger & Impeller Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070aigcs The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 16 TP 400-4148-01-IW-S Auger & Impeller Group REF NO PART NO. 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1715091SM 1928721SM 2805123SM 1960474SM 1715120A 1612093SM 1666425SM 2836098SM 1721680SM 1660655SM 1670971SM 1666424SM 1676027SM 7092126SM 1726733SM 1721676SM 1676026SM 1726538SM 1676024SM 1726732SM 2860625SM 7092125SM 2821133SM 1726536SM 1726535SM 1918447SM 1668344SM 1960114SM 2827794SM 7015894SM 1612112SM 7092127SM QTY. DESCRIPTION 1 2 2 1 1 1 1 1 1 1 1 1 2 6 1 1 2 1 1 1 1 6 1 1 1 2 2 4 2 1 1 12 PULLEY, Auger Input SET SCREW, 5/16-18 x 1/2 ” Square Head Cup Point KEY, 3/16 x 3/4 ” Woodruff SET SCREW, 3/8-16 x 1/2 ” Square Head IMPELLER ASSEMBLY OIL SEAL BUSHING PIN, Drive-Loc, 3/16 x 1-1/2 ” COLLAR, Thrust SHAFT, Rolled Worm WASHER, Thrust (.562 ID x 1.000 OD x .030/.032 Thick) FLANGE, Bushing OIL SEAL NUT 1/4-20 Hex Center Lock GEAR CASE, RH- Intermediate GASKET, Gear Case BUSHING SHAFT, Auger, 22 “/24 ” GEAR, Worm GEAR CASE, LH- Intermediate PIPE PLUG, 1/8-27 NPTF 3/4 Taper x .31 Long Hex Drive SCREW, 1/4-20 x 7/8 ” Hex Head Cap, GR 5 FITTING, Grease AUGER ASSEMBLY, 22 ” RH AUGER ASSEMBLY, 22 ” LH COTTER PIN, 3/32 x 3/4 ” SHEAR PIN, .248 ID x 1-3/4 ” Long WASHER RING, Retaining KEY, #605 Woodruff TUBE, Low Density Polyethylene Extruded FLAT WASHER, .268 ID x .591 OD x .063 Thick Footnotes The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 17 TP 400-4148-01-IW-S Auger Housing Group NOTE: Unless noted otherwise, use the standard hardware torque specification chart. 070ch3pc The above parts group applies to the following Mfg. Nos.: 1694587 – 555M 1694588 – 860E 1694595 – 555M 1694596 – 860M Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. 18 TP 400-4148-01-IW-S Auger Housing Group REF NO PART NO. 1 2 2 3 4 5 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 7072543SM 7072548SM 7072568SM 1930659SM 7072546SM 1675080A 1725352A 1726457SM 1665982ASM 2108202SM 1727854CSM 1916965SM 1931315SM 1925205SM 1930641SM 1960711SM 1924940SM 1960687SM 7091841SM 7072551SM 1917356SM 1929000SM 7011938SM 7091075SM 1716632SM 7091076SM 2860210SM 1706085SM 7073192SM 7090316SM QTY. DESCRIPTION 1 1 1 3 1 1 1 2 1 1 2 4 12 3 12 4 4 4 6 2 3 5 3 6 1 2 3 2 1 1 END PLATE, RH- …..
1/4-28 5/16-18 5/16-24 3/8-16 3/8-24 7/16-14 7/16-20 1/2-13 1/2-20 9/16-12 9/16-18 5/8-11 5/8-18 3/4-10 3/4-16 7/8-9 7/8-14 1-8 1-12 in/lbs ft/lbs 19 20 27 31 66 76 11 12 20 23 30 35 50 55 65 75 90 100 160 180 140 155 220 240 Nm. 2.1 2.3 3.1 3.5 7.6 8.6 15.0 16.3 27.2 31.3 40.8 47.6 68.0 74.8 88.4 102.0 122.4 136 217.6 244.8 190.4 210.8 299.2 326.4 in/lbs ft/lbs 30 31 43 49 8 10 17 19 30 35 50 55 75 90 110 120 150 180 260 300 400 440 580 640 NOTES Nm. 3.4 3.5 4.9 5.5 10.9 13.6 23.1 25.8 40.8 47.6 68.0 74.8 102.0 122.4 149.6 163.2 204.0 244.8 353.6 408.0 544.0 598.4 788.8 870.4 in/lbs ft/lbs Nm. 4.6 4.9 6.8 7.7 16.3 19.0 34.0 34.0 61.2 68.0 95.2 108.8 149.6 163.2 204.0 231.2 299.2 326.4 525.0 571.2 816.0 897.6 1,244.0 1,360.0 The guides and ruler furnished below are designed to help you select the appropriate hardware and tools. 0 Nut, 1/2 ” Inside Diameter Screw, 1/2 x 2 2 Body Diameter Body Length 41 43 60 68 12 14 25 27 45 50 70 80 110 120 150 170 220 240 386 420 600 660 900 1,000 Wrench & Fastener Size Guide 1/4 1/4 ” Bolt or Nut Wrench–7/16 ” 1/4 1/2 3/4 1 1/4 1/2 3/4 1/4 1/2 3/4 1. These torque values are to be used for all hardware excluding: locknuts, self-tapping screws, thread forming screws, sheet metal screws and socket head setscrews. 2. Recommended seating torque values for locknuts: a. for prevailing torque locknuts – use 65% of grade 5 torques. b. for flange whizlock nuts and screws – use 135% of grade 5 torques. 3. Unless otherwise noted on assembly drawings, all torque values must meet this specification. 3 1/4 1/2 3/4 4 5/16 5/16 ” Bolt or Nut Wrench–1/2 ” 3/8 3/8 ” Bolt or Nut Wrench–9/16 ” 7/16 DIA. 7/16 ” Bolt or Nut Wrench (Bolt)–5/8 ” Wrench (Nut)–11/16 ” 1/2 DIA. 1/2 ” Bolt or Nut Wrench–3/4 ” MANUFACTURING, INC. 500 N. Spring Street / PO Box 997 Port Washington, WI 53074-0997 USA www.simplicitymfg.com Briggs and Stratton Yard Power Products Group 2008 by Briggs and Stratton Corporation Milwaukee, WI, USA. …
Wikipedia’s page for Simplicity Outdoor
Publisher: www.simplicitymfg.com
0 Responses
Stay in touch with the conversation, subscribe to the RSS feed for comments on this post.